About this item

• ➤REPLACEMENT FOR : It can Replacement For Volkswagen Eos Tiguan GTI CC Passat Beetle Jetta Audi A3 A4 Q5 A6 A6 Quattro
• ➤SUPERSEDED PART NUMBER:06H998907A ,06H 998 907,06 H 998 907A,06H998907A,06G 998 907,06G998907,06J 998 907,06J 998 907,06J 998 907A,06J998907A
• ➤HIGH-QUALITY MATERIALS：Perfect Performanc.Easy Installation.High Reliability.We use high-quality rubber O-rings It can improve the performance, and easy to install, high reliability Our Products are 100% Perfect Match for the Original Car.
• ➤SERVICE：Please confirm the product part number before purchase. If you are not sure whether it fits your car, please contact us
• ➤WHAT YOU GET - 4 SET Fuel Injectors Seals Repair Kit

SUPERSEDED PART NUMBER:06H998907A ,06H 998 907,06 H 998 907A,06H998907A,06G 998 907,06G998907,06J 998 907,06J 998 907,06J 998 907A,06J998907A

Package includes

Fuel injector Seals Repair Kit x4

• Replacement For AUDI A3 (8V1, 8VK) 1.8 TFSI 04.2012 -A3 Convertible (8V7, 8VE) 1.8 TFSI 10.2013 -A3 Limousine (8VS, 8VM) 1.8 TFSI 05.2013 -A3 Sportback (8PA) 2.0 TFSI 09.2004 - 03.2013A3 Sportback (8PA) 2.0 TFSI quattro 09.2004 - 03.2013A3 Sportback (8VA, 8VF) 1.8 TFSI 09.2012 -A4 (8K2, B8) 1.8 TFSI 01.2008 - 12.2015A4 (8K2, B8) 1.8 TFSI 11.2007 - 03.2012A4 (8K2, B8) 2.0 TFSI 06.2008 - 12.2015A4 Allroad (8KH, B8) 2.0 TFSI quattro 04.2009 - 05.2016A4 Allroad (8KH, B8) 2.0 TFSI quattro 05.2013 - 05.2016A5 (8T3) 1.8 TFSI 05.2009 - 09.2011A5 (8T3) 1.8 TFSI 10.2007 - 01.2017 A5 Convertible (8F7) 2.0 TFSI quattro 03.2009 - 01.2017A5 Sportback (8TA) 1.8 TFSI 11.2009 - 09.2017A6 (4G2, 4GC, C7) 1.8 TFSI 09.2014 - 09.2018A6 Avant (4G5, 4GD, C7) 1.8 TFSI 09.2014 - 09.2018
• Replacement For VW AMAROK (2HA, 2HB, S1B, S6B, S7A, S7B) 2.0 TSI 12.2010 - 10.2016 BEETLE (5C1, 5C2) 2.0 TSI 04.201CC (358) 2.0 TSI 11.2011 - 12.2016 1 - 07.2016 EOS (1F7, 1F8) 2.0 TFSI 03.2006 - 08.2015 GOLF ALLTRACK VII (BA5, BV5) 1.8 TSI 4motion 12.2014 - GOLF V (1K1) 2.0 GTI 10.2004 - 02.2009 GOLF V Variant (1K5) 2.0 06.2007 - 07.2009 GOLF VI (5K1) 2.0 GTi 04.2009 - 11.2012 JETTA III (1K2) 2.0 TFSI 10.2005 - 10.2010 GOLF VI Variant (AJ5) 2.0 TSI 07.2009 - 07.2013 GOLF VI Convertible (517) 2.0 GTI 05.2012 - 05.2016 PASSAT (3G2, CB2) 1.8 TSI 02.2015 - PASSAT ALLTRACK (365) 2.0 TSI 4motion 01.2012 - 12.2014 PASSAT Variant (3C5) 2.0 FSI08.2005 - 11.2010 TIGUAN (5N_) 2.0 TSI 4motion 05.2011 - 07.2018 TIGUAN (5N_) 2.0 TSI 4motion 05.2011 - 07.2018 TOURAN (5T1) 1.8 TSI TRANSPORTER T5 Bus (7HB, 7HJ, 7EB, 7EJ, 7EF, 7EG, 7HF, 7EC) 2.0 TSI 4motion 07.2011 - 08.2015 11.2015 -

• Carefully clean cylinder head bore of high-pressure injection valve without using lubricant.Do not damage surface of bore.

Install high-pressure injection valve without lubricant in cylinder head (do not apply lubricant tocombustion chamber sealing ring).

• Figure 1: The O-ring (1) and combustion chamber sealing ring (3) must always be replaced.
• Figure 2:Removing combustion chamber sealing ring: Carefully remove old combustion

Chamber sealing ring (3) using a suitable tool. Do not damage groove or web in floorof groove.

• Figure 3: Position assembly arbour(A) on high-pressure injection valve(4).Pull new combustion chamber sealing ring (3) by hand over assembly arbour into groove of valve body.Do not use any lubricant. To calibrate the combustion chamber sealing ring, pushadjusting ring(B) with bevelled outer side all the way over the combustion chambersealing ring. Turn adjusting ring applying only moderate force 180° in one directionand then 180° back again to the starting position.

• Flgure 4: Do not increase diameter of support disk when installing.Turn like a screw over collar.Ensure support disk is installed correctly.

Flat side without step must face towards O-ring.

• Figure 5: Applying force to the plastic housing of the sensor will destroy component (A) To tighten, only apply force to the attached hexagon(B).
• Figure 6: Comply with tightening torque of plastic high-pressure sensor: 20...24 Nm

Note:The sensor has a taper seat. After tightening, an air gap(A) to the fuel distributorremains. Do not use additional seals and do not continue to tighten sensor.